View B1101UC4LXX_559380.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

SIDACtor (R) Protection Thyristors
SLIC Protection
Battrax(R) Series - Dual Port Negative -
MS-013
Description The Dual Port Negative Battrax(R) Series are programmable SIDACtor(R) devices designed to protect SLICs (Subscriber Line Interface Circuit) from damaging overvoltage transients. Dual port protection is provided by a programmable device that is referenced to a negative voltage souce while internal diodes provide protection from positive surge events. Features and Benefits Low voltage overshoot Low on-state voltage Agency Approvals
Agency Agency File Number E133083
Dual-port protection Gate trigger tracking device Integrated diode for positive voltage surges
Does not degrade with use Fails short circuit when surged in excess of ratings Applicable Global Standards TIA-968-A
Pinout Designation
1 2 3 6 5 4
GR 1089 Intra-building IEC 61000-4-5 YD/T 1082 YD/T 993 YD/T 950
TIA-968-B ITU K.20/21 Enhanced Level ITU K.20/21 Basic Level GR 1089 Inter-building
Schematic Symbol
(T1) 1 6 (T2)
5 Ground (-VREF) 2
(R1) 3
4 (R2)
Electrical Characteristics
VDRM @lDRM=5A V min B1101UC4LXX B1161UC4Lxx B1201UC4Lxx B1101UC4 B1161UC4 B1201UC4 I-VREF I-VREF I-VREF VS @100V/s V max I-VREF I-VREF I-VREF IH IS IT A max 2.2 2.2 2.2 VT @IT=2.2 Amps V max 4 4 4 VF V max 5 5 5 Capacitance* pF min pF max 30 30 30 200 200 200
Part Number
Marking
mA min mA max 100 160 200 100 100 100
Notes: - Absolute maximum ratings measured at TA= 25C (unless otherwise noted). - Devices are uni-directional - All electrical characteristics shown are defined from Tip (pin 1 & 6) to Ground (pin 5) and Ring (pin 3 & 4) to Ground (pin 5)
- VREF Max Value for the negative Battrax is -200 V. - XX = Part Number Suffix: `TP' (Tube Pack) or `RP' (Reel Pack). * Off-state capacitance (CO) is measured across pins 1 & 5, 3 & 5, 4 & 5, and 6 & 5 at 1 MHz with a 2V bias.
(c) 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information.
126 Revised: February 22, 2011
SIDACtor (R) Protection Thyristors
SLIC Protection
Surge Ratings
IPP Series 0.2x310 0.5x700 2
1
ITSM 5x320 1 9x720 2 A min 200 10x360 1 10x360 2 A min 175 10x1000 1 10x1000 2 A min 100 5x310 1 10x700 2 A min 200 50/60 Hz A min 50
2x10 2x10 2
1
8x20 1.2x50 2
1
10x160 10x160 2
1
10x560 1 10x560 2 A min 150
di/dt A/s max 500
A min C
Notes: 1 Current waveform in s 2 Voltage waveform in s
A min 500
A min 400
A min 200
50
- Peak pulse current rating (IPP) is repetitive and guaranteed for the life of the product. rating assumes VREF - IPP PP - The device must initially be in thermal equilibrium with -40C < TJ <
Thermal Considerations
Package Modified MS-013
6 5 4 1 2 3
Symbol TJ TS R0JA
Parameter Operating Junction Temperature Range Storage Temperature Range Thermal Resistance: Junction to Ambient
Value
Unit C C
60
C/W
V-I Characteristics
+I V
tr x td Pulse Waveform
IPP - Peak Pulse Current - %IPP
100
VREF VS VDRM -V IDRM IH IS IT
IPP
PIN 5 CONNECTED TO GROUND Pin 1-2: PIN 2 CONNECTED TO VREF PIN 2 CONNECTED TO GROUND
Peak Value
tr = rise time to peak value td = decay time to half value
VT
IF
Waveform = tr x td
+V
50
Half Value
0 0 tr td t - Time (s)
-I
PIN 3 CONNECTED TO VREF
Normalized VS Change vs. Junction Temperature
Normalized DC Holding Current vs. Case Temperature
14
2.0
Percent of VS Change - %
10
IH (TC = 25C)
12
1.8 1.6 1.4 1.2 1.0 0.8 0.6 0.4
-40 -20 0 20 40 60 80 100 120 140 160
6 4 2 0 -4 -6 -8 -40 -20 0
IH
8
25 C
25C
20 40 60 80 100 120 140 160
Ratio of
Junction Temperature (TJ) - C
Case Temperature (TC) - C
(c) 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information.
127 Revised: February 22, 2011
SIDACtor (R) Protection Thyristors
SLIC Protection
Soldering Parameters
Reflow Condition
- Temperature Min (Ts(min))
Pb-Free assembly (see Fig. 1)
Figure 1
TP
Ramp-up
tP
Critical Zone TL to TP
Pre Heat
- Temperature Max (Ts(max)) - Time (Min to Max) (ts)
60-180 secs.
Temperature
Average ramp up rate (Liquidus Temp (TL) to peak) TS(max) to TL - Ramp-up Rate Reflow
- Temperature (TL) (Liquidus) - Temperature (tL)
TL TS(max)
Preheat
3C/sec. Max. 3C/sec. Max. 60-150 secs.
tL
Ramp-down
TS(min)
tS
Peak Temp (TP) Time within 5C of actual Peak Temp (tp) Ramp-down Rate Time 25C to Peak Temp (TP) Do not exceed 30 secs. Max. 6C/sec. Max. 8 min. Max.
25 time to peak temperature (t 25C to peak)
Time
Physical Specifications
Lead Material Terminal Finish Body Material Copper Alloy 100% Matte-Tin Plated
Environmental Specifications
High Temp Voltage Blocking 80% Rated VDRM (VDC Peak 504 or 1008 hrs. MIL-STD-750 (Method 1040) JEDEC, JESD22-A-101 cycles. MIL-STD-750 (Method 1051) EIA/JEDEC, JESD22-A104 52 VDC JEDEC, JESD22-A-101 JEDEC, JESD22-A-101 -65C, 1008 hrs. 10 cycles. MIL-STD-750 (Method 1056) JEDEC, JESD22-A-106 JEDEC, JESD22-A-102
Temp Cycling
UL recognized epoxy meeting flammability classification 94V-0
Biased Temp & Humidity High Temp Storage Low Temp Storage Thermal Shock Autoclave (Pressure Cooker Test) Resistance to Solder Heat Moisture Sensitivity Level
Part Numbering
Part Marking
B1 xx 1 U C 4 L xx
TYPE
B1: Negative Battrax SIDACtor
PACKING OPTIONS
RP: Reel Pack TP: Tube Pack
XXXXXXXX XXXXX
Part Marking Code
(Refer to Electrical Characteristics Table)
HOLDING CURRENT
10: 100 mA 20: 200 mA 16: 160 mA
CONSTRUCTION VARIABLE PACKAGE TYPE
RoHS COMPLIANT DUAL PORT IPP RATING
Date Code
(c) 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information.
128 Revised: February 22, 2011
SIDACtor (R) Protection Thyristors
SLIC Protection
Dimensions -- MS-013
Dimensions
Pad Outline C 0.138 (3.50) E 0.059 (1.50) 0.065 (1.65) 0.460 (11.68) Dimension are in inches (and millimeters).
Inches Min 0.360 0.352 0.400 0.043 0.047 0.293 0.289 0.089 0.041 0.020 0.133 Max 0.364 0.356 0.412 0.045 0.055 0.297 0.293 0.093 0.049 --0.143
Millimeters Min 9.14 8.94 10.16 1.09 1.19 7 .44 7 .34 2.26 1.04 0.51 3.38 Max 9.25 9.04 10.46 1.13 1.40 7 .54 7 .44 2.36 1.24 --3.63
7 TYP A
D 7 TYP G A J H Burr Side 96 4 7 TYP B A F 7 TYP MIN Length of Flat K Detail A
Mold Split Line BSC*
A B C D E F G H J K BSC*
* BSC = Basic Spacing between Centers
Packing Options
Package Type Description Modified MS-013 6-pin Tape and Reel Pack Quantity Added Suffix
Industry Standard
1500 500 (50 per tube)
RP TP
EIA-481-D N/A
U
Modified MS-013 6-pin Tube Pack
Tape and Reel Specification -- MS-013
.157 (4.0)
.630 (16.0) .512 (13.0) Arbor Hole Dia.
.472 (12.0) 12.99 (330)
Dimensions are in inches (and millimeters)
0.700 (17.8)
Direction of Feed
Tube Pack Specification -- MS-013
Message Location .020 .005 WALL TYP. (0.51 0.13)
.108 (2.74) .110 (2.79)
.045 (1.14) 90 .165 (4.19)
.310 (7.87) 6 Interior of the Tube
20.000 .030 (508.00 0.76)
.005 A
.150 (3.81)
.225 (5.72) .525 (13.34)
A
Dimensions are in inches (and millimeters)
(c) 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information.
129 Revised: February 22, 2011

▲Up To Search▲

Price & Availability of B1101UC4LXX

	To Download B1101UC4LXX Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .